Nitotile GTA Price in Bangladesh

Description

Nitotile GTA Price in Bangladesh (Granite and Marble Tiles Adhesive)

Uses:
Nitotile GTA is a single part high quality polymer based adhesive for the permanent fi xing of granite granite,marble &
stone tiles.

Advantages:

•  Prepacked product requiring only direct mixing water at site.
• High adhesive bond strength – Ideal for vertical and
  horizontal applications of granite, marble, etc.
• Excellent grab during open time
• Smooth easy to mix and spread
• Can be used in the interior and exterior of buildings

Standard Compliance:
IS 15477-2019 TYPE 3

Properties:

Mixed Density                               1.50 to 1.90 gm/cc

W/P ratio                                       0.26 to 0.30

Bed Thickness                              Up to 6mm (can be extended
up to 12 mm thickness in
area of limited extent)

Pot Life                                         >120 Mins

Open Time                                    >20 Mins

Tensile Adhesion Strength
Dry Condition                                1.5 MPa
Wet Condition                               1.0 MPa

Shear Adhesion Strength:
Dry Condition                                1.5 MPa
Wet Condition                               1.0 MPa
Heat Aging Condition                    1.0 MPa

Adjustability                                   >15 mins

Slip                                                < 0.5mm in vertical
application

Note: The typical physical properties given above are derived from testing in a controlled laboratory environment. Results
derived from testing fi eld-applied samples may vary, dependent on actual site conditions.

Application instructions
Surface preparation
All surfaces must be sound and thoroughly cleaned before Nitotile GTA is applied. All traces of grease and oil must be
removed. All loose particles of mortar, wallpaper, paint etc., must be physically removed. The prepared surface must be
wetted with water, prior to application of Nitotile GTA and must attain a saturated surface dry condition. Nitotile GTA can be applied directly on concrete, cement screeds, cement or lime mortars, provided they are strong. Make sure the substrate is Fl at and in sound conditions to achieve uniform thickness & coverage. Saturate the surface thoroughly and remove excess water before the application of Nitotile GTA For porous substrates, it is recommended to use suitable primer.

Mixing:
Nitotile GTA should be mixed with clear potable water in the water powder ratio of 0.26 to 0.30. A slow speed drill fitted with a mixing paddle is recommended for mixing. Add powder to water and mix until a uniform, lump-free consistency is achieved. The total quantity of water may be slightly adjusted to achieve the required consistency.

Pack Size                            (Kg) Water required (Litres)

20                                         5.6 to 6
40                                         11.2 to 12

Application:
Make sure that required amount of adhesive shall be mixed & used within the specific ed pot life. Spread not more than the
area which can be filed within the.

open time of the adhesive.
2. Using a notch trowel, uniformly comb the tile adhesive to required thickness.

3. Firmly fi x the tiles into position with a slight twisting action, ensuring good contact without leaving any voids behind tiles.

4. Tiles should be fixed within specific ed open time of adhesive, depending on the porosity of the substrate and atmospheric conditions. Adhesive ribs can be checked periodically and if a skin has formed, remove the adhesive and apply a new layer. 5. Spacers & corner beads of required dimensions shall be used to maintain adequate joints between individual tiles on horizontal or vertical areas.

6. Remove any excess adhesive from the tiles and joints with a damp sponge or cloth before it sets. Leave for at least one
day before application of tile grouts. It is recommended to use Nitotile cementitious/epoxy tile grouts.

Limitations:
Nitotile GTA is not recommended for overhead applications. On vertical applications, heavy slabs need proper support till
appropriate grab is achieved

Note : Nitotile GTA should not be applied on Gypsum board substrates. Any height more than 3 mt needs clamping.

Estimating
Supply
Nitotile GTA : 20 & 40 Kgs

Coverage
Nitotile GTA : Approx. 3.40 to 3.60 kg/sq. meter @ 3mm thickness using 6mm x 6mm square notch trowel.

Note : Actual yield will vary according to water addition Coverage may depend upon the nature and fl atness of the substrate:
and the method of application.

Storage:
Shelf life – 12 months in unopened bags under normal warehouse condition

Precautions
Health and safety
Nitotile GTA contains cement powders which, when mixed with water or upon becoming damp, release alkalis which can
be harmful to the skin. Hence, use hand gloves of type Butyl Rubber and vinyl. During use, avoid inhalation of the dust and contact with the skin or eyes. Wear suitable protective clothing – eye protection, gloves and respiratory equipment, particulate fi later, type P2 (particularly in confied spaces). The use of barrier creams to provide additional skin protection is
also advised. In case of contact with the skin, rinse with plenty of clean water, then cleanse thoroughly with soap and water. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately – do not induce vomiting.

Additional information
FOSguard is registered brand owned by FOSROC for building care products. With our commitment to our valued customers for providing a complete solution for the buildings we have host of products including waterproofi ng, repairs, grouts, anchors protective coatings, sealants , mould release agents and
curing compounds “YOU BUILD. WE PROTECT” is our commitment from the
brand of FOSguard For further information please contact our local Fosroc offi ce