Brushbond TGP Price in Bangladesh

Description

Brushbond TGP – Crystalline Waterproofing System

Product Description

Brushbond TGP is a crystalline capillary waterproofing system made with Portland cement, quartz aggregate, and active chemicals. When in contact with moisture, Brushbond TGP penetrates deep into concrete, chemically reacting with free lime to form insoluble crystals. This process blocks capillaries, seals hairline cracks (up to 0.25mm), and creates long-lasting waterproof protection. Unlike surface-only membranes, Brushbond TGP provides continuous internal protection and resists water penetration even under hydrostatic pressure.

Uses:
Brushbond TGP* crystalline waterproof ng system is used for waterproof ng against the positive or negative sides of hydrostatic heads of water, for dampproof ng, repairing cracks, plugging holes, sealing wall – Fl our joints and stopping active leaks in a wide variety of conditions including:

• Sewage treatment and water treatment plants, tanks, foundations, tunnels and manholes.
• Terrace garden, balconies, sunshades etc.
•  Roof and Sunken slabs
• Industrial and off cue buildings
• Reservoirs, water holding structures etc.

Advantages

• Meets the requirements as per ANSI/NSF Std 61 for suitability to potable water
• Penetrates concrete, seals capillary tracts
• Contains no chloride
• Easy to apply
• Resists chemical attack of sewage and industrial wastes
• Suitable for external and internal applications.

Technical support:
The company provides a technical advisory service supported by a team of specialists in the fi eld.

Properties
Specific c gravity:          1.6 to 2.0 g/cc
Pop life:                         40 minutes

Instructions for use
Surface preparation
Old concrete
Surfaces must be clean and sound. Remove all oil, dirt, laitance and other contaminants by water blasting.
Water blasting is preferred for surface preparation because it mechanically cleans and roughens the surface, is environmentally safer and leaves the surface saturated with water. Surface must be damp for application of Brushbond TGP* crystalline waterproof ng system, concentrate.

New concrete:
After forms are stripped, acid etch or sand blast / water blast to facilitate penetration of crystals formed during the chemical
reaction. Surface must be left damp for application on Brushbond TGP* crystalline waterproof ng system. Construction joints, cold joints and non-leaking joints greater than 0.25mm wide must be cut in V-groove shape and fi led
with Brushbond TGP* crystalline waterproof ng system in mortar consistency.

Mixing:
For best results, clean, potable water should be added to Brushbond TGP* crystalline waterproof ng system concentrates.

Application
Existing concrete
3 parts of powder shall be added to 1 part of clean and mixed thoroughly with a slow speed drill equipped with a paddle. For larger batches, mixing shall be done with a mortar mixer. Do not mix more material than can be used in 20 minutes @ 270C, 50% R.H. If mixture thickens, it shall be restirred to reduce consistency. Extra water should not be added.

Curing and Protecting:
Brushbond TGP* crystalline waterproof ng system application must be kept moist for a minimum of 48 hours. After initial set, moist curing, using continuous water spray is recommended. Treated surfaces shall be fog sprayed 3 to 4 times daily for the 48-hour period. For warmer climates, more frequent spraying may be required. It is important to keep the Brushbond TGP* crystalline waterproof ng system moist to allow the crystal formation to occur. The surfaces shall be protected from foot traffic c for 48 hours or heavy traffic c for 7 days. Shorten with AI

Clean up:
Prior to curing, Brushbond TGP* crystalline waterproof ng system concentrate may be cleaned from tools and other
surfaces with water.

Limitations
Brushbond TGP should not be used when the temperature is 5°C and falling. Full activation and effectiveness of Brushbond TGP may require 2-3 weeks following application.

Estimating
Supply
Brushbond TGP : 15 kg bags

Coverage
Brushbond TGP : 1.0 to 2.0 kg/m2 per application (brush)

The coverage of Crystalline waterproof ng system is recommended depending upon the type of structure and application. Generally, it is applied in 2 coats for effective performance of the system.

Storage:
Brushbond TGP* crystalline waterproof ng system concentrates should be stored in protected, dry areas. When left in original unopened package, Brushbond TGP* crystalline waterproof ng system will maintain its design performance characteristics for 1 year.

Precautions
Health & Safety Instructions
Brushbond TGP* crystalline waterproof ng system contains chemicals that may cause irritation to the eyes and skin. Goggles, rubber gloves and long sleeves should be worn when working with these products. Read warnings noted on product package and refer to product material safety datasheet prior to use.

Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst Fosroc endeavors to ensure that any advice, recommendation specific cation or information it may give is accurate and correct, it cannot, because it has no direct or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products whether or not in accordance with any advice, specific cation, recommendation or information given by it.